ProductsElectric Wire Rope

UR Type Series Inverter hoist 1t  ∼ 2.8(3)t

Inverter technology and creep speed technology are combined to make a variable speed hoist for twenty-first century.

 
 
400V class debut
 
 

The inside of Control box

 
Inverter for hoisting
Inverter for traversing
(Option)
Contactor for
High speed lowering
Contactor for Inverter
 
 

Operation image of inverter hoist

 
 

Moving pattern by push button operation

 
 

• Excellent Operativeness

The new control system which combines Inverter operation and contactor operation for the first time in the industry realises smooth operativeness and quick response of stop and speed reduction. In addition, low hoisting speed can be selected from 3 speed types. In the case of hoist with traversing inverter, high speed can be selected from 4 speed types  and   low  speed  can  be  selected from  2  speed  types.   In comparison with the conventional creep type, the setting range is wider.

 

• Improvement of maintenance

Since its structure part is the same as general purpose hoist, the number of parts decreased significantly compared with the conventional creep type. And the maintenance is easy as its control parts are made into one board.

 

• Effect of conservation of energy

As UR type does not use a regenerative resistor, it is more power saving compared to U type. The durability of its brake disk becomes about double in comparison with that of the conventional creep type.
 

• Excellent cost performance

The UR series is variable speed hoist very high in cost performance.

Features(comparison with the U series, conventional creep type hoist)

Item

UR series

Conventional creep type

U series

 

Control system
(Lifting/Lowering)

Inverter and contactor operation Lifting (both low and high speed):
Inverter control
Lowering at low speed: inverter control
Lowering at high speed: contactor operation

contactor operation
Change two  motor with clutch

Inverter

Control system(Traversing)

Inverter

Pole change or two motors

Inverter

 

Speed setting
(Lifting/Lowering)

High speed: Fixed(Normal speed)
Low speed: select from 1/10,1/6,1/4
of high speed

High speed: Fixed (Normal speed)
Low speed: Fixed
(1/10 of  Normal speed)

Setting is possible at arbitrary speed with high speed, the low speed between 1/10
of normal speed - normal speed

 

Speed setting(Traversing)

High speed: select from 25, 20, 15, 10m/min
Low speed: select from 2.5, 5/min

High speed : Fixed
Low speed : Fixed
Speed ratio 1:1/4 or 1:1/5

Setting is possible at arbitrary speed with high speed, the low speed between 1/10
of normal speed - normal speed

Respons for the operation

Slow start, Sudden stop*

Sudden start, Sudden stop

Slow start, Slow stop

Operative cost

Medium

High

Low

Power consumption

Low

Low

Medium

Number of parts

Small

Large

Medium

* At lifting, it stops as the cushion working, and At lowring, it stops by sudden deceleration.
* Rope specification of 1t 2falls is 6 x Fi (29)
Note 1 : The values in the table are referential values.
Note 2 : In the case of 400V Class (Including 380V) , there may be differences in outline dimension. Please contact us.

Standard Specifications

  • Power supply
    • **** 3-phase 200V 50/60Hz control 200V, 220V 60Hz control 220V (400V class is also available)
    • **** 3-phase 400V 50/60Hz control 200V, 440V 60Hz control 220V
    • **** 3-phase 380V 50Hz control 48V(100V and 24V are also available)
  • Operating method Push button switch operation.
     

    1/2t  ∼ 3t

    Suspended type
    Frame mounted type

    2 Points

    U D

    Motor operated traversing hoist

    6 Points

    U D E W S N

    * Above push buttons are all 2 step push buttons excluding "ON" and "OFF"
  • Applicable standard
    *** JISC9620 Electric Hoist, Crane structure standard
  • Rating
    *** Hoisting:25% ED(63% of rating load), 150S/Hr JISC9620, Travelling:3O min. JISC9620
  • Power supply system
    *** Cable feeding, Trolley feeding (limited to Double trolley type)
  • Ambient air temperature
    *** -10°C ∼ 40°C (Non congelation)
  • Ambient relative humidity
    *** Less than 90% RH (Non condensing)
  • Enclosure
    *** Simplified outdoor type(JISC 0920, Equivalent to IP44) (Rainproof cover is required, when it is used in the open air.)
  • Color coating
    *** Main body: Metallic gray (Equevalent to Munsell N4.0)
    Hook block: Munsell 7.5YR7/14
    Pushbutton: Equivalent to Munsell 7.5YR7/13
    Note: These hoists cannot be used for lift (elevator for passengers.)
Remarks
• High lowering is contactor operation, speed is 6m/min in 1t and 6.7m/min in 2t•2.8t for the power supply of 50Hz.
• Lifting low speed is set to 1/10 of high-speed at shipment.
• High speed traversing/low speed traversing is set to 25/2.5m/min at shipment.
Caution
• UR Series are not possible to use for the lift.
• When the winding creep is done, it is not possible to operate smoothly by the traversing resistance. Please contact us.
• We recommend the installation of the noise filler because it might mis-operate in the point where a lot of power supply noises exist
• Please contact us when you use the product in a lot of places such as the causticity gas and dust that are.
• Speed range of lifting and lowering in low speed is ±40% of the display value in the ratings load. The speed difference between much load end no load grows at the time of a low speed operating, too.


Back